Cisco CCNA Certification Training: Etherchannels And Spanning Tree Protocol (STP) — CCIE Training

Cisco CCNA Certification Training: Etherchannels And Spanning Tree Protocol (STP)

Article by Chris Bryant, CCIE #12933

Cisco CCNA certification looks great on your resume, and it also teaches you vital real-world networking skills. One exam topic that you’ll definitely see in today’s networks is the configuration of an Etherchannel on a Cisco router. You need to know how to build and verify one – so let’s build one right now!

In this Cisco training tutorial, we’ll use two switches that are connected at ports 0/11 and 0/12 via crossover cables. SW1 is the root bridge, SW2 is the non-root bridge. Even though there are two separate physical connections, spanning tree protocol (STP) will only allow the use of one, as verified by the partial output of “show spanning vlan 1” on SW2.

Fa0/11 Root FWD 19 128.11 P2p

Fa0/12 Altn BLK 19 128.12 P2p

It’s a waste of network resources not to use that second physical path. Additionally, there’s going to be a delay in cutting over from 0/11 to 0/12 if the forwarding path goes down. We can get around both of these issues by creating an Etherchannel. An Etherchannel is a logical bundling of physical paths into one logical path. By configuring an Etherchannel on both 0/11 and 0/12, we will be left with one logical connection that will actually use the full capacity of both physical connections!

SW1(config)#int fast 0/11

SW1(config-if)#channel-group 1 mode on

Creating a port-channel interface Port-channel 1

The channel-group command must be configured on each physical interface that we want to place into the Etherchannel, so we’ll have to configure it on ports 0/11 and 0/12 on both SW1 and SW2. Naturally, the group number used must match among all ports placed into the Etherchannel.

Did you notice the router message “creating a port-channel interface port-channel 1”? You can verify the creation of that virtual interface just as you would a physical interface:

SW1#show int port-channel 1

Port-channel1 is up, line protocol is up (connected)

Hardware is EtherChannel, address is 000f.90e1.c24b (bia 000f.90e1.c24b)

Note the readout “Hardware is EtherChannel”. Also, where we once saw two physical ports when we ran “show spanning vlan 1”, we now see only one – the port-channel. Also note that where the individual ports had a port cost of 19, the Etherchannel has a cost of 12 due to its increased bandwidth capabilities.

Po1 Desg FWD 12 128.65 P2p

Etherchannels give us a performance benefit and a fault tolerance benefit as well. Performance is increased since all physical channels between the two switches can be used, rather than the one STP allows by default. Fault tolerance is also increased, since a physical channel bundled into the Etherchannel can go down without an STP recalculation — STP sees the Etherchannel as one single connection!

Etherchannels aren’t just important to know about for the CCNA exam, they’re commonly used in real-world networks as well – so make sure you know how to configure and troubleshoot them!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA certification and CCNP tutorials! For my FREE “How To Pass The CCNA” course, visit the website! Attend Cisco CCNA training from The Bryant Advantage!

Know someone that could use this CCIE Training information? Send this page by clicking on the SHARE button below:

Bookmark and Share

{ 1 comment… read it below or add one }

chase4net August 16, 2012 at 10:04 am

About Our CCNA Course

The CCNA certification (Cisco Certified Network Associate) indicates a foundation course if you want to be a network Engineer. CCNA certified professionals can install, configure, and operate LAN, WAN, and dial access services for small networks (100 nodes or fewer), including but not limited to use of these protocols: IP, IGRP, Serial, Frame Relay, IP RIP, VLANs, RIP, Ethernet, Access Lists.

Node of Teaching : 60% Hands-On, 40% Lecture

This Cisco CCNA class at Chase4Net features real world, hands-on lab time with actual routers and switches. The majority of the class involves live interaction with real network hardware that will be applied on the job as a network administrator. Our Cisco instructors have large amounts of industry experience and carry a minimum of the CCNA certification – but most frequently they have CCNP or CCIE as well as certification from other vendors. We also offer custom built corporate CCNA training classes with on-site instruction at your facility. If your interested in receiving a quote for a custom CCNA course, visit our corporate IT training page for more information.

Our CCNA Training Options are

1) YOu Join one of our open enrollment, hands-on training classes at our office chennai locations.

2) you can also our other online services such as ccna Interview questions, Interview Preparation , self paced training course. Call -9884925203 or 044-64130523

Chase4Net Provides training on the following IT courses in ChennAi DOTNET,JAVA ,LINUX

Reply

Leave a Comment

Before you click Submit, solve this math puzzle captcha: *

Previous post:

Next post: